PFSense Konsolen Netzwerkeinstellungen - Versionsgeschichte

Thomas.will: /* Grundeinstellung */

2022-02-13T09:21:32Z

Grundeinstellung

Thomas.will: /* Die Idee */

2022-02-10T15:12:44Z

Die Idee

Thomas.will am 10. Februar 2022 um 15:12 Uhr

2022-02-10T15:12:24Z

Thomas.will: /* Grundeinstellung */

2022-02-10T15:08:40Z

Grundeinstellung

Thomas.will: /* Grundeinstellung */

2022-02-10T15:05:25Z

Grundeinstellung

Thomas.will am 10. Februar 2022 um 15:03 Uhr

2022-02-10T15:03:26Z

Thomas.will: /* Erstes Setup */

2022-02-10T14:59:29Z

Erstes Setup

Thomas.will: Die Seite wurde neu angelegt: „=Erstes Setup= Should VLANs be set up now [y|n]?n Enter the WAN interface name or 'a' for auto-detection (vtnet0 vtnet1 vtnet2 or a): vtnet0 *Enter the LA…“

2022-02-10T14:59:04Z

Die Seite wurde neu angelegt: „=Erstes Setup= *Should VLANs be set up now [y|n]?n *Enter the WAN interface name or 'a' for auto-detection (vtnet0 vtnet1 vtnet2 or a): vtnet0 *Enter the LA…“

Neue Seite

=Erstes Setup=
*Should VLANs be set up now [y|n]?n
*Enter the WAN interface name or 'a' for auto-detection
(vtnet0 vtnet1 vtnet2 or a): vtnet0
*Enter the LAN interface name or 'a' for auto-detection
NOTE: this enables full Firewalling/NAT mode.
(vtnet1 vtnet2 a or nothing if finished): vtnet1
*Enter the Optional 1 interface name or 'a' for auto-detection
(vtnet2 a or nothing if finished): vtnet2

@@ Zeile 42: / Zeile 42: @@
 </pre>
 *Enter an option:2
-<pre>
+*[[PFSense 2) Set interface(s) IP address| 2) Set interface(s) IP address]]
-- WAN (vtnet0 - dhcp, dhcp6)
+;Entsprechned für die anderen Netze
 =Resultat=
 <pre>

@@ Zeile 1: / Zeile 1: @@
 =Die Idee=
-*Grundsetup der Netzwerkschnitteln
+*Grundsetup der Netzwerkschnittstellen
 *Auswahl WAN, LAN und OPT (später DMZ)
 *Default Gateway
 *DHCP Grundkonfiguration
 *PFSense danach über das Lan Interface per Web administrierbar
 =Erstes Setup=

← Nächstältere Version		Version vom 10. Februar 2022, 15:12 Uhr
Zeile 1:		Zeile 1:
		+	=Die Idee=
		+	*Grundsetup der Netzwerkschnitteln
		+	*Auswahl WAN, LAN und OPT (später DMZ)
		+	*Default Gateway
		+	*DHCP Grundkonfiguration
		+	*PFSense danach über das Lan Interface per Web administrierbar
		+
		+
	=Erstes Setup=		=Erstes Setup=
	*Should VLANs be set up now [y\|n]?n		*Should VLANs be set up now [y\|n]?n

← Nächstältere Version		Version vom 10. Februar 2022, 15:08 Uhr
Zeile 71:		Zeile 71:
	</pre>		</pre>
	;Entsprechned für die anderen Netze		;Entsprechned für die anderen Netze
		+	=Resultat=
		+	<pre>
		+	KVM Guest - Netgate Device ID: 2151ca91e52d2dc565fc
		+
		+	* Welcome to pfSense 2.5.2-RELEASE (amd64) on pfSense *
		+
		+	WAN (wan) -> vtnet0 -> v4: 194.59.156.201/27
		+	LAN (lan) -> vtnet1 -> v4: 192.168.151.1/24
		+	OPT1 (opt1) -> vtnet2 -> v4: 192.168.101.1/24
		+
		+	0) Logout (SSH only) 9) pfTop
		+	1) Assign Interfaces 10) Filter Logs
		+	2) Set interface(s) IP address 11) Restart webConfigurator
		+	3) Reset webConfigurator password 12) PHP shell + pfSense tools
		+	4) Reset to factory defaults 13) Update from console
		+	5) Reboot system 14) Enable Secure Shell (sshd)
		+	6) Halt system 15) Restore recent configuration
		+	7) Ping host 16) Restart PHP-FPM
		+	8) Shell
		+
		+	Enter an option:
		+	</pre>

@@ Zeile 35: / Zeile 35: @@
 </pre>
 *Enter an option:2
+<pre>
 Available interfaces:
@@ Zeile 41: / Zeile 41: @@
 - LAN (vtnet1 - static)
 - OPT1 (vtnet2)
+</pre>
-Enter the number of the interface you wish to configure: 1
+*Enter the number of the interface you wish to configure: 1
+*Configure IPv4 address WAN interface via DHCP? (y/n) n
-Configure IPv4 address WAN interface via DHCP? (y/n) n
+*Enter the new WAN IPv4 address.  Press <ENTER> for none:
+ > 194.59.156.201
-Enter the new WAN IPv4 address.  Press <ENTER> for none:
+ Subnet masks are entered as bit counts (as in CIDR notation) in pfSense.
-> 194.59.156.201
+ e.g. 255.255.255.0 = 24
+.255.0.0   = 16
-Subnet masks are entered as bit counts (as in CIDR notation) in pfSense.
+.0.0.0     = 8
-e.g. 255.255.255.0 = 24
+*Enter the new WAN IPv4 subnet bit count (1 to 31):
-.255.0.0   = 16
+ > 27
-.0.0.0     = 8
+*For a WAN, enter the new WAN IPv4 upstream gateway address.
+*For a LAN, press <ENTER> for none:
-Enter the new WAN IPv4 subnet bit count (1 to 31):
+ > 194.59.156.193
-> 27
+*Configure IPv6 address WAN interface via DHCP6? (y/n) n
+*Enter the new WAN IPv6 address.  Press <ENTER> for none:
 For a WAN, enter the new WAN IPv4 upstream gateway address.
-For a LAN, press <ENTER> for none:
+ Disabling IPv4 DHCPD...
-> 194.59.156.193
+ Disabling IPv6 DHCPD...
+*Do you want to revert to HTTP as the webConfigurator protocol? (y/n) y
-Configure IPv6 address WAN interface via DHCP6? (y/n) n
+<pre>
 Please wait while the changes are saved to WAN...
   Reloading filter...
@@ Zeile 77: / Zeile 69: @@
 The IPv4 WAN address has been set to 194.59.156.201/27
+</pre>
 ;Entsprechned für die anderen Netze

← Nächstältere Version		Version vom 10. Februar 2022, 15:03 Uhr
Zeile 14:		Zeile 14:

	*Do you want to proceed [y\|n]? y		*Do you want to proceed [y\|n]? y
		+	=Grundeinstellung=
		+	<pre>
		+	KVM Guest - Netgate Device ID: 2151ca91e52d2dc565fc
		+
		+	* Welcome to pfSense 2.5.2-RELEASE (amd64) on pfSense *
		+
		+	WAN (wan) -> vtnet0 -> v4/DHCP4: 194.59.156.217
		+	LAN (lan) -> vtnet1 -> v4: 192.168.1.1/24
		+	OPT1 (opt1) -> vtnet2 ->
		+
		+	0) Logout (SSH only) 9) pfTop
		+	1) Assign Interfaces 10) Filter Logs
		+	2) Set interface(s) IP address 11) Restart webConfigurator
		+	3) Reset webConfigurator password 12) PHP shell + pfSense tools
		+	4) Reset to factory defaults 13) Update from console
		+	5) Reboot system 14) Enable Secure Shell (sshd)
		+	6) Halt system 15) Restore recent configuration
		+	7) Ping host 16) Restart PHP-FPM
		+	8) Shell
		+	</pre>
		+	*Enter an option:2
		+
		+	Available interfaces:
		+
		+	1 - WAN (vtnet0 - dhcp, dhcp6)
		+	2 - LAN (vtnet1 - static)
		+	3 - OPT1 (vtnet2)
		+
		+	Enter the number of the interface you wish to configure: 1
		+
		+	Configure IPv4 address WAN interface via DHCP? (y/n) n
		+
		+	Enter the new WAN IPv4 address. Press <ENTER> for none:
		+	> 194.59.156.201
		+
		+	Subnet masks are entered as bit counts (as in CIDR notation) in pfSense.
		+	e.g. 255.255.255.0 = 24
		+	255.255.0.0 = 16
		+	255.0.0.0 = 8
		+
		+	Enter the new WAN IPv4 subnet bit count (1 to 31):
		+	> 27
		+
		+	For a WAN, enter the new WAN IPv4 upstream gateway address.
		+	For a LAN, press <ENTER> for none:
		+	> 194.59.156.193
		+
		+	Configure IPv6 address WAN interface via DHCP6? (y/n) n
		+
		+	Enter the new WAN IPv6 address. Press <ENTER> for none:
		+	>
		+	Disabling IPv4 DHCPD...
		+	Disabling IPv6 DHCPD...
		+
		+	Do you want to revert to HTTP as the webConfigurator protocol? (y/n) y
		+
		+	Please wait while the changes are saved to WAN...
		+	Reloading filter...
		+	Reloading routing configuration...
		+	DHCPD...
		+	Restarting webConfigurator...
		+
		+	The IPv4 WAN address has been set to 194.59.156.201/27
		+
		+	;Entsprechned für die anderen Netze

← Nächstältere Version		Version vom 10. Februar 2022, 14:59 Uhr
Zeile 8:		Zeile 8:
	*Enter the Optional 1 interface name or 'a' for auto-detection		*Enter the Optional 1 interface name or 'a' for auto-detection
	(vtnet2 a or nothing if finished): vtnet2		(vtnet2 a or nothing if finished): vtnet2
		+
		+	WAN -> vtnet0
		+	LAN -> vtnet1
		+	OPT1 -> vtnet2
		+
		+	*Do you want to proceed [y\|n]? y

PFSense Konsolen Netzwerkeinstellungen - Versionsgeschichte

Thomas.will: /* Grundeinstellung */

Thomas.will: /* Die Idee */

Thomas.will am 10. Februar 2022 um 15:12 Uhr

Thomas.will: /* Grundeinstellung */

Thomas.will: /* Grundeinstellung */

Thomas.will am 10. Februar 2022 um 15:03 Uhr

Thomas.will: /* Erstes Setup */

Thomas.will: Die Seite wurde neu angelegt: „=Erstes Setup= *Should VLANs be set up now [y|n]?n *Enter the WAN interface name or 'a' for auto-detection (vtnet0 vtnet1 vtnet2 or a): vtnet0 *Enter the LA…“

Thomas.will: Die Seite wurde neu angelegt: „=Erstes Setup= Should VLANs be set up now [y|n]?n Enter the WAN interface name or 'a' for auto-detection (vtnet0 vtnet1 vtnet2 or a): vtnet0 *Enter the LA…“