VLAN mit Linux und Cisco Nexus: Unterschied zwischen den Versionen
Zur Navigation springen
Zur Suche springen
| Zeile 70: | Zeile 70: | ||
;Ethernet1/2 und Ethernet1/3 → VLAN 22 (SERVER) | ;Ethernet1/2 und Ethernet1/3 → VLAN 22 (SERVER) | ||
<pre> | <pre> | ||
| − | interface Ethernet1/2 | + | interface Ethernet1/2-3 |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
description VLAN 22 SERVER | description VLAN 22 SERVER | ||
switchport mode access | switchport mode access | ||
| Zeile 91: | Zeile 85: | ||
spanning-tree port type edge | spanning-tree port type edge | ||
</pre> | </pre> | ||
| + | end | ||
| + | copy running-conf startup-conf | ||
==IP im MGMT NETZ Vergeben= | ==IP im MGMT NETZ Vergeben= | ||
Version vom 2. Juli 2025, 09:03 Uhr
Zielbeschreibung
- Der Cisco-Port Ethernet1/1 ist als 802.1Q-Trunk konfiguriert.
- Der Linux-Rechner verwendet das Interface enp0s10.
- Zwei VLANs werden getaggt übertragen:
- VLAN 22 → 172.16.213.1/24
- VLAN 23 → 172.18.213.1/24
Plan
Voraussetzungen auf Debian/Linux
- VLAN-Paket installieren
- apt install vlan
- VLAN-Modul laden
- sudo modprobe 8021q
- Modul beim Booten automatisch laden
- echo 8021q | sudo tee -a /etc/modules
/etc/network/interfaces
auto lo iface lo inet loopback auto enp0s10 iface enp0s10 inet manual auto enp0s10.22 iface enp0s10.22 inet static address 172.16.213.1 netmask 255.255.255.0 vlan-raw-device enp0s10 auto enp0s10.23 iface enp0s10.23 inet static address 172.18.213.1 netmask 255.255.255.0 vlan-raw-device enp0s10
Zum Cisco
- ssh localhost -p 3022
oder im Notfall
- nc localhost 2023
- Logindaten
- user: admin
- pass: admin
VLAN anlegen
configure terminal vlan 22 name SERVER vlan 23 name MGMT end copy running-config startup-config
Cisco-Konfiguration für Ethernet1/1
configure terminal
interface Ethernet1/1 no switchport access vlan 99 description Trunk zu Linux-Host switchport mode trunk switchport trunk allowed vlan 22,23 spanning-tree port type edge trunk
Cisco-Konfiguration für Access-Ports
- Ethernet1/2 und Ethernet1/3 → VLAN 22 (SERVER)
interface Ethernet1/2-3 description VLAN 22 SERVER switchport mode access switchport access vlan 22 spanning-tree port type edge
- Ethernet1/4 und Ethernet1/5 → VLAN 23 (MGMT)
interface Ethernet1/4-5 description VLAN 23 MGMT switchport mode access switchport access vlan 23 spanning-tree port type edge
end copy running-conf startup-conf
=IP im MGMT NETZ Vergeben
Aktivierung der Konfiguration
Nach den obigen Anpassungen auf dem Linux-System die Netzwerkschnittstellen neu starten:
- sudo systemctl restart networking
- ip addr show
- Sicherstellen, dass die IP-Adressen korrekt zugewiesen wurden und die Kommunikation innerhalb der VLANs funktioniert.
