WLAN AccessPoint: Unterschied zwischen den Versionen
Zur Navigation springen
Zur Suche springen
| (28 dazwischenliegende Versionen von 5 Benutzern werden nicht angezeigt) | |||
| Zeile 1: | Zeile 1: | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | == | + | =Installation= |
| − | = | + | *apt install bridge-utils hostapd |
| − | + | =Forward= | |
| − | + | ;/etc/sysctl.conf: | |
| − | + | net.ipv4.ip_forward = 1 | |
| − | + | *sysctl -p | |
| − | |||
| − | |||
| − | == | + | =Interfaces= |
| + | ;/etc/network/interfaces | ||
| + | <pre> | ||
| + | auto vmbr0 | ||
| + | iface vmbr0 inet static | ||
| + | address 10.10.10.1 | ||
| + | netmask 255.255.255.0 | ||
| + | dns-nameservers 10.80.100.103 | ||
| + | dns-search hack.lab | ||
| + | bridge_ports none | ||
| + | bridge_stp off | ||
| + | bridge_fd 0 | ||
| + | bridge_maxwait 0 | ||
| + | </pre> | ||
| + | *ifup -v vmbr0 | ||
| − | == | + | =hostapd= |
| + | */etc/hostapd | ||
| + | <pre> | ||
| + | interface=wlan0 | ||
| + | bridge=vmbr0 | ||
| + | driver=nl80211 | ||
| + | ssid=CHEWINGGUM | ||
| + | hw_mode=g | ||
| + | channel=6 | ||
| + | macaddr_acl=0 | ||
| + | auth_algs=1 | ||
| + | ignore_broadcast_ssid=0 | ||
| + | wpa=2 | ||
| + | wpa_passphrase=9twin-towers11 | ||
| + | wpa_key_mgmt=WPA-PSK | ||
| + | wpa_pairwise=TKIP | ||
| + | rsn_pairwise=CCMP | ||
| + | </pre> | ||
| + | *systemctl unmask hostapd | ||
| + | *systemctl enable hostapd --now | ||
| − | + | = Links = | |
| + | * https://wiki.ubuntuusers.de/Netzwerkbr%C3%BCcke/#Bruecken-in-drahtlose-Netze | ||
* http://ubuntuforums.org/showthread.php?t=400236&page=118 | * http://ubuntuforums.org/showthread.php?t=400236&page=118 | ||
* http://www.linux.com/learn/tutorials/442417-create-a-secure-linux-based-wireless-access-point | * http://www.linux.com/learn/tutorials/442417-create-a-secure-linux-based-wireless-access-point | ||
| Zeile 29: | Zeile 52: | ||
* http://rt2x00.serialmonkey.com/wiki/index.php/AP-mode_Howto | * http://rt2x00.serialmonkey.com/wiki/index.php/AP-mode_Howto | ||
* http://git.kernel.org/?p=linux/kernel/git/dwmw2/linux-firmware.git;a=tree | * http://git.kernel.org/?p=linux/kernel/git/dwmw2/linux-firmware.git;a=tree | ||
| + | * https://help.ubuntu.com/community/NetworkConnectionBridge | ||
Aktuelle Version vom 19. August 2021, 18:41 Uhr
Installation
- apt install bridge-utils hostapd
Forward
- /etc/sysctl.conf
net.ipv4.ip_forward = 1
- sysctl -p
Interfaces
- /etc/network/interfaces
auto vmbr0 iface vmbr0 inet static address 10.10.10.1 netmask 255.255.255.0 dns-nameservers 10.80.100.103 dns-search hack.lab bridge_ports none bridge_stp off bridge_fd 0 bridge_maxwait 0
- ifup -v vmbr0
hostapd
- /etc/hostapd
interface=wlan0 bridge=vmbr0 driver=nl80211 ssid=CHEWINGGUM hw_mode=g channel=6 macaddr_acl=0 auth_algs=1 ignore_broadcast_ssid=0 wpa=2 wpa_passphrase=9twin-towers11 wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP
- systemctl unmask hostapd
- systemctl enable hostapd --now
Links
- https://wiki.ubuntuusers.de/Netzwerkbr%C3%BCcke/#Bruecken-in-drahtlose-Netze
- http://ubuntuforums.org/showthread.php?t=400236&page=118
- http://www.linux.com/learn/tutorials/442417-create-a-secure-linux-based-wireless-access-point
- http://mcbridematt.dhs.org/blog/tag/wireless
- http://rt2x00.serialmonkey.com/phpBB/viewtopic.php?f=5&t=5203
- http://rt2x00.serialmonkey.com/wiki/index.php/AP-mode_Howto
- http://git.kernel.org/?p=linux/kernel/git/dwmw2/linux-firmware.git;a=tree
- https://help.ubuntu.com/community/NetworkConnectionBridge