Sophos 2 cisco asa: Unterschied zwischen den Versionen

Aus Xinux Wiki
Zur Navigation springen Zur Suche springen
David (Diskussion | Beiträge)
Keine Bearbeitungszusammenfassung
David (Diskussion | Beiträge)
Keine Bearbeitungszusammenfassung
Zeile 1: Zeile 1:
=interfaces einrichten=
=interfaces einrichten=


configure terminal
configure terminal
  interface Vlan2
  interface Vlan2
  ip address 192.168.244.185 255.255.248.0  
  ip address 192.168.244.185 255.255.248.0  
Zeile 15: Zeile 15:
  end
  end


=auf cisco=


  configure terminal
  configure terminal
  access-list acl-asa-toc extended permit ip 10.20.170.0 255.255.255.0 10.20.0.0 255.255.0.0
crypto ikev1 policy 10
authentication pre-share
encryption aes-256
hash md5
group 5
lifetime 28800
crypto ikev1 enable if-outside
 
 
  access-list acl-asa-soph extended permit ip 10.20.170.0 255.255.255.0 10.20.0.0 255.255.0.0
  crypto isakmp identity address
  crypto isakmp identity address
  crypto isakmp enable if-outside
  crypto isakmp enable if-outside
  crypto ipsec transform-set AES256-MD5 esp-aes-256 esp-md5-hmac
  crypto ipsec transform-set AES256-MD5 esp-aes-256 esp-md5-hmac
  crypto map vpn-asa-toc 10 match address acl-asa-toc
  crypto map vpn-asa-soph 10 match address acl-asa-soph
  crypto map  vpn-asa-toc 10 set pfs group5
  crypto map  vpn-asa-soph 10 set pfs group5
  crypto map vpn-asa-toc 10 set peer 192.168.244.130
  crypto map vpn-asa-soph 10 set peer 192.168.244.130
  crypto map  vpn-asa-toc 10 set ikev1 transform-set AES256-MD5
  crypto map  vpn-asa-soph 10 set ikev1 transform-set AES256-MD5
  crypto map  vpn-asa-toc interface if-outside
  crypto map  vpn-asa-soph interface if-outside
  tunnel-group 192.168.244.130 type ipsec-l2l  
  tunnel-group 192.168.244.130 type ipsec-l2l  
  tunnel-group 192.168.244.130 ipsec-attributes  
  tunnel-group 192.168.244.130 ipsec-attributes  
  pre-shared-key streng-geheim
  pre-shared-key streng-geheim
  object network no-nat
  end
subnet 10.20.0.0 255.255.0.0
nat (if-inside,if-outside) source static obj-lan obj-lan destination static no-nat no-nat

Version vom 18. März 2016, 10:31 Uhr

interfaces einrichten

configure terminal
interface Vlan2
ip address 192.168.244.185 255.255.248.0 
 nameif if-outside
interface Vlan1                     
 nameif if-inside
ip address 10.20.170.1 255.255.255.0
route if-outside 0.0.0.0 0.0.0.0 192.168.240.100
domain-name xinux.org
dns domain-lookup if-outside
dns server-group DefaultDNS
name-server 192.168.240.200
end


auf cisco

configure terminal
crypto ikev1 policy 10
authentication pre-share
encryption aes-256
hash md5
group 5
lifetime 28800
crypto ikev1 enable if-outside


access-list acl-asa-soph extended permit ip 10.20.170.0 255.255.255.0 10.20.0.0 255.255.0.0
crypto isakmp identity address
crypto isakmp enable if-outside
crypto ipsec transform-set AES256-MD5 esp-aes-256 esp-md5-hmac
crypto map vpn-asa-soph 10 match address acl-asa-soph
crypto map  vpn-asa-soph 10 set pfs group5
crypto map vpn-asa-soph 10 set peer 192.168.244.130
crypto map  vpn-asa-soph 10 set ikev1 transform-set AES256-MD5
crypto map  vpn-asa-soph  interface if-outside
tunnel-group 192.168.244.130 type ipsec-l2l 
tunnel-group 192.168.244.130 ipsec-attributes 
pre-shared-key streng-geheim
end